Best Electric Scooter Phone Holder & Mounts: Secure Handlebar Options Compared

A dependable electric scooter phone holder does far more than keep Google Maps in view during a commute. Stand-up electric scooters combine small 8.5-inch to 11-inch wheels, stiff aluminum forks, high-pressure or solid tires, and crowded handlebars packed with thumb throttles, brake levers, bells, turn-signal switches, and center LED dashboards. Because pavement seams and potholes transfer sharp shock directly up the steering column, a casual bicycle mount that works fine on a cruiser bike can rotate, droop, or drop a phone on an e-scooter.

Before ordering any clamp, measure both the outer diameter and the width of the exposed round bar section on your scooter. If you are mounting a phone on a pedal-assist bicycle instead, see our guide to the best phone mounts for electric bikes, or browse our main phone mounts hub for every vehicle category.

Best Electric Scooter Phone Holder Picks Compared

The four mounts below cover everything from compact 15mm to 22.2mm commuter scooter handlebars to oversized 31.8mm (1-1/4 inch) tubular bars on high-speed dual-motor scooters.

Fitment note: Measure the exact section of exposed round tubing where you plan to install the clamp before ordering. Many scooters taper or flatten near the center display housing.

What Makes a Good Electric Scooter Phone Mount?

Electric kick scooters create four mechanical challenges that riders rarely face on a standard pedal bicycle.

• Narrow horizontal bar clearance matters as much as bar diameter: While many commuter scooters use standard 22mm to 22.2mm (7/8-inch) round tubing near the grips, the center of the bar is almost always occupied by an integrated LED display and power button. Once you account for the right-hand thumb throttle, left-hand brake lever, bell latch, and turn-signal switch housing, you may only have 0.75 to 1.25 inches (19mm to 32mm) of exposed metal tubing for a clamp band.
• Handlebar profiles vary wildly across scooter brands: Never assume every e-scooter uses a uniform 22.2mm bicycle bar across its entire width. Some commuter models use cast aluminum or plastic shrouds that flare toward the center stem, while higher-powered dual-motor scooters step up to 31.8mm (1-1/4 inch) fatbars at the stem clamp.
• Mechanical retention outperforms bare magnetic mounts: Hitting a sunken utility cover or expansion joint at 15 to 25 mph on small 8.5-inch or 10-inch scooter tires sends a sharp vertical impulse through the rigid steering stem. A four-corner cradle, locking side clamp, or mechanical twist-lock case connection resists sheer forces that can knock a phone off a flat magnetic pad.
• Ball joints and collars must resist downward droop: A clamp without proper rubber sizing shims or a locking ball collar will slowly rotate downward over brick or rough asphalt, forcing you to take a hand off the bar to readjust the screen.

Best Electric Scooter Phone Mounts Reviewed

1. Lamicall Bike Phone Holder

The Lamicall Bike Phone Holder (model BM02-B) is our top value pick for everyday commuter kick scooters. Although Lamicall uses a bicycle-focused product name, the clamp assembly is engineered for bicycles, e-bikes, motorcycles, and stand-up electric scooters.

What makes the Lamicall especially adaptable to electric scooters is its wide clamping span. Using four removable silicone sizing pads inside the ring clamp, it grips round handlebars ranging from 0.59 inches to 1.57 inches (15mm to 40mm) in diameter. That 15mm minimum diameter is a major advantage on compact scooters where the only open mounting spot is a thin auxiliary crossbar, mirror stalk, or narrow outer grip section, while the 40mm maximum easily clears thicker round steering stems.

Instead of relying on spring tension alone, the Lamicall cradle wraps around all four corners of the phone and includes a red mechanical locking switch on the rear housing. Once you slide a 4.7-inch to 6.8-inch smartphone into the top-and-bottom jaws (supporting devices up to 0.59 inches / 15mm thick including a standard protective case), flipping the rear lock switch prevents the cradle arms from backing out over rough pavement. A 360-degree ball joint allows portrait or landscape viewing without requiring a proprietary phone case.

Best for: Everyday commuters on Segway Ninebot, Xiaomi, Gotrax, or Hiboy scooters who want an affordable, case-friendly mechanical cradle that fits 15mm to 40mm round bars.

View on Amazon →

2. JOYROOM Motorcycle Phone Mount

The JOYROOM Motorcycle Phone Mount (model JR-ZS288) is the strongest universal choice if you make frequent stops and want true one-handed phone loading and removal. Rather than requiring you to pull the top jaw upward with one hand while sliding your phone in with the other, JOYROOM uses a center trigger button on the face of the cradle: press the phone against the center button and the four corner arms snap shut around the device automatically.

After the arms close, a secondary locking lever on the back of the cradle locks the ratcheting mechanism so pothole impacts cannot pop the jaws open. To release the phone at the end of your ride, you unlock the rear switch and press the side release bars with one hand. The cradle accommodates smartphones from 4.7 to 7.0 inches, giving it plenty of room for an iPhone Pro Max, Samsung Galaxy S Ultra, or Google Pixel Pro in a protective case.

The tool-free handlebar clamp fits round bars from 0.7 inches to 1.34 inches (18mm to 34mm) using the included silicone shims, and its 360-degree swivel ball lets you angle the screen directly toward your line of sight. Keep in mind that while JOYROOM lines the four corner claws and bar clamp with thick silicone cushioning to stop rattling and surface scratches, rubber cradle pads are not the same as a tuned elastomer vibration isolator for high-speed riding on broken streets.

Best for: Delivery riders, urban commuters, and riders with 4.7-inch to 7.0-inch phones who want fast one-handed docking on 18mm to 34mm round scooter bars.

View on Amazon →

3. Tackform 20MAXX All-Metal Phone Mount

If you ride a faster dual-motor electric scooter with suspension and bicycle-style tubular handlebars, or if you regularly commute over torn-up city streets where plastic ball sockets flex and crack, the Tackform 20MAXX All-Metal Phone Mount (Enduro Series) is the heavy-duty upgrade.

Unlike consumer plastic holders, Tackform machines both the cradle chassis and the dual-socket arm from 6061-T6 billet aluminum anchored to a 20mm metal ball-and-socket platform. The hinged aluminum handlebar clamp fits 7/8-inch (22.2mm), 1-inch (25.4mm), and 1-1/4-inch (31.8mm) round bars using the included split reducer bushings. Because it bolts down with an Allen screw rather than a bulky hand-turn plastic knob, the clamp footprint is narrow enough to tuck neatly between hydraulic brake master cylinders and multi-switch pods on performance scooters.

The spring-loaded aluminum cradle holds phones up to 3.7 inches wide and 0.6 inches thick, and Tackform encapsulates the internal stainless steel support pins in thermoplastic sleeves to eliminate the metallic buzzing common on cheaper metal cradles. Octagonal rubber grip pads also hold the back of the phone slightly off the aluminum backplate to promote airflow on hot summer rides. The only trade-off is weight and industrial styling: it is overkill for a 12 mph lightweight scooter, but unmatched in structural rigidity on 30+ mph machines.

Best for: High-performance electric scooters with 22.2mm to 31.8mm tubular bars, rough city pavement, and riders who want zero plastic flex.

View on Amazon →

4. Quad Lock Out Front Mount

The Quad Lock Out Front Mount (model QLM-OFM-2) is our top premium pick for riders who rely on turn-by-turn navigation every day and need to solve a crowded center handlebar. Instead of clamping the edges of your phone with bulky side jaws, Quad Lock uses a patented dual-stage twist-lock interface that mates the mount head directly to a model-specific Quad Lock Case or adhesive Universal Adapter (sold separately).

What makes the Out Front Mount uniquely effective on an electric scooter is its cantilevered, reversible arm. Using the supplied EPDM rubber spacers, the narrow band clamp fits 22mm (7/8 inch), 25.4mm (1 inch), 31.8mm (1-1/4 inch), and 35mm (1-3/8 inch) round bars. Once clamped right next to your scooter’s center stem or display housing, the arm extends forward—or can be flipped backward over the stem—so your phone floats cleanly in front of or above the scooter’s built-in speedometer rather than taking up grip space near the throttle.

While the upfront cost is higher because you must purchase a compatible Quad Lock phone case or Universal Adapter, the mount leaves almost nothing on the handlebar when your phone is in your pocket, and the same case clicks onto bicycle, car, and motorcycle mounts across the Quad Lock mounts ecosystem.

Best for: Daily scooter commuters who want a low-profile mechanical twist-lock mount that positions the phone ahead of a center scooter display and supports a bolt-on vibration dampener.

View on Amazon →

Fitment by Electric Scooter Handlebar Style

Before tightening a clamp, match your mount to one of the three common electric scooter cockpit layouts:

• Standard Commuter Kick Scooters (Segway Ninebot Max G30P / G30LP, Xiaomi Mi M365 / Pro 2, Hiboy S2, Gotrax GXL / G4): These models typically use 22mm to 22.2mm (7/8-inch) round tubing between the center dashboard and the rubber handgrips, but horizontal bar width is tight—often only 18mm to 30mm of exposed bar on the left side next to the brake lever and bell. Both the Lamicall (with its medium silicone shims) and the Quad Lock Out Front Mount (with the 22mm spacer) fit this section cleanly.
• Wide Center-Shroud & Enclosed Cockpits (NIU KQi2 Pro / KQi3 Max, Segway Ninebot Max G2 / F2 Pro, Apollo City): Many newer commuter scooters wrap the center of the handlebar in a sculpted rectangular or triangular plastic shroud that tapers into the grips, leaving very little cylindrical tubing. Measure the round section immediately inboard of the left grip before ordering; if less than 15mm of straight round bar is exposed, install a compact 22.2mm clamp-on handlebar extender bar first or mount to the exposed round vertical steering stem below the top clamp (staying completely clear of the lower folding hinge).
• Performance & Dual-Motor Scooters (Kaabo Mantis / Wolf Warrior, Apollo Phantom, VSETT 9+ / 10+, Dualtron, Segway GT Series): Most high-speed scooters use motorcycle- or mountain-bike-style tubular handlebars that measure 22.2mm (7/8 inch) near the controls and bulge to 31.8mm (1-1/4 inch) at the center riser clamp. The CNC aluminum Tackform 20MAXX and Quad Lock Out Front Mount both include 31.8mm hardware to clamp directly next to the center stem.

If you ride a sit-down, step-through moped or motor scooter (such as a Vespa, Genuine Buddy, Honda PCX, or NIU NQi GTS) where painted plastic bodywork completely encloses the handlebars, none of these bar clamps will work. Instead, attach your holder to the exposed mirror stalks using one of the setups in our motorcycle mirror stem phone mounts guide.

Where Should You Mount a Phone on an Electric Scooter?

Because an electric scooter handlebar is significantly narrower than a bicycle or motorcycle bar, placement affects both screen visibility and control safety:

• Left side of the center display (Best for most riders): Mounting just inboard of the left brake lever and bell keeps your right hand completely free to operate the thumb or finger throttle without obstruction.
• Out front over the center stem: Using an offset arm like the Quad Lock Out Front Mount positions the screen along your natural centerline without covering the scooter’s built-in speedometer, battery meter, or riding-mode indicator. Verify that the forward-extending arm does not hit the rear fender hook when the stem is folded down for carrying.
• Right side near the throttle (Use extreme caution): Most electric scooters place a spring-returned thumb throttle on the right side. Only mount a phone on the right if the clamp, cradle, and phone in both portrait and landscape orientations leave generous clearance around the throttle lever through its full arc of travel.
• Upper vertical stem tube: If your top handlebar is fully enclosed by a plastic dashboard, clamping to a straight, round section of the vertical steering column right below the top T-junction is a workable alternative. Never clamp a phone mount over a folding latch, safety collar, stem telescoping joint, or external brake cable routing slot.

Common Electric Scooter Phone Mount Problems and Fixes

• The handlebar has no room Left of the display: Try sliding the left handgrip, brake lever perch, or bell 5mm to 10mm outward (if your bar design allows), switch to a narrow-band out-front mount like the Quad Lock that only needs 12mm to 15mm of bar width, or add a small clamp-on handlebar accessory extender bar.
• The mount rotates downward after hitting bumps: Ensure the clamp is seated on a cylindrical section of metal tubing rather than a tapered plastic shroud. Add the next thickest rubber spacer pad included with your mount so the clamp halves compress the rubber firmly before bottoming out against each other.
• The phone buzzes or blurs at speed: Solid honeycomb tires and high tire pressures transmit sharp road buzz into the handlebars. Move the clamp closer to the center stem to reduce lever-arm flex, avoid long multi-joint plastic extension arms, and add a dedicated elastomer vibration isolator if you ride daily with an OIS-equipped smartphone.
• The phone blocks the folding stem hook: Many kick scooters fold at the base of the stem and latch onto a hook on the rear fender via a ring attached to the handlebar bell. Check your folding geometry with the empty mount installed so the cradle does not prevent the stem latch from clicking shut.

How to Install an Electric Scooter Phone Mount Step by Step

1. Select a straight, rigid clamping spot: Park the scooter on its kickstand on level ground and find a cylindrical section of the handlebar (usually on the left side between the center display and the brake lever/bell) where the clamp will sit completely flat.
2. Fit the correct rubber sizing shims: Wrap the manufacturer’s EPDM rubber or silicone spacer strips around the bar first. These shims adapt the clamp to 15mm, 22.2mm, 25.4mm, or 31.8mm tubing and provide the friction needed to stop rotation over potholes.
3. Set your viewing angle before final torque: Loosely attach the clamp, insert your phone, and step onto the scooter deck in your normal standing riding posture. Angle the cradle toward your eyes so you only need a quick downward glance, then tighten the clamp hardware evenly.
4. Lock the ball collar and test clearances: Tighten the rear ball-joint nut firmly, engage the cradle’s mechanical safety lock, and perform a full left-to-right steering, brake, throttle-return, and stem-folding check before taking a short test ride on smooth pavement.

Electric Scooter Phone Mount FAQ

Will a standard bicycle phone mount work on an electric scooter?

Many bicycle mounts physically clamp onto electric scooters that use standard 22.2mm (7/8-inch) round handlebars, provided there is enough open bar width beside the center display and controls. However, skip open silicone stretch bands and magnet-only bike mounts; small scooter wheels transmit much harsher vertical impacts over potholes than 26-inch to 29-inch bicycle wheels, so a locked four-corner cradle or mechanical twist-lock mount is strongly recommended.

What handlebar diameter do most electric scooters use?

Most commuter kick scooters (including Segway Ninebot Max G30, Xiaomi Mi M365, Gotrax, and Hiboy models) use 22mm to 22.2mm (7/8-inch) round bars near the grips, while dual-motor performance scooters frequently use 22.2mm outer bars that flare to 31.8mm (1-1/4 inch) at the center stem clamp. Always measure the exact mounting spot with calipers or a flexible tape measure before ordering.

Is a bare MagSafe mount secure enough for an electric scooter?

No. While magnetic MagSafe mounts are convenient inside a car cabin, hitting a sharp curb cut or pothole on small scooter wheels creates high shear force that can slide or pop a heavy phone right off an unlatched magnet. Always use a mechanical four-corner cradle (such as Lamicall, JOYROOM, or Tackform) or a mechanical twist-lock case interface (such as Quad Lock).

Can electric scooter vibration damage my phone camera?

Yes, prolonged high-frequency road vibration—especially on scooters with solid rubber tires or stiff forks ridden over rough asphalt and brick—can degrade smartphone optical image stabilization (OIS) and autofocus sensors over time. Apple specifically advises using a vibration-dampening mount on mopeds and electric scooters to protect camera hardware.

How do I mount a phone on a scooter with a wide plastic center screen and no bar space?

If a wide dashboard shroud (such as on a NIU KQi3 or Segway Ninebot Max G2) leaves less than 15mm of exposed round bar next to the grips, your best options are a narrow-band out-front mount (which needs only about 12mm to 14mm of clamp width), a clamp-on handlebar extender bar, or clamping to a straight cylindrical section of the vertical steering stem below the top handlebar tee.

Bottom Line: Which Electric Scooter Phone Mount Should You Buy?

For the vast majority of commuter scooter riders, start with the Lamicall Bike Phone Holder: its 15mm to 40mm clamp range fits almost any exposed round bar or stem tube, and its four-corner cradle with a rear lock switch secures your phone without forcing you into a proprietary case. Step up to the JOYROOM Motorcycle Phone Mount if you want fast one-handed push-button docking on 18mm to 34mm bars, choose the CNC-machined Tackform 20MAXX All-Metal Phone Mount for faster dual-motor scooters with 22.2mm to 31.8mm tubular handlebars, or invest in the Quad Lock Out Front Mount (paired with a Quad Lock Case and Vibration Dampener) for the cleanest over-display navigation setup.

If you also ride heavier two-wheelers or want to compare more rugged powersports hardware, check out our full roundup of the best motorcycle phone mounts and our motorcycle mirror stem phone mounts guide for sit-down mopeds and motor scooters.